Skip to main content
Precharge

Guide : DC DC converters precharge

Which precharge sequence for your DC DC converter ?

Precharge

Definition

Precharge is the first step in each system starting up. Precharge consist in limiting the voltage supply into an electrical system via an auxiliary power supply circuit. Precharge hence allows a moderated power up with no damage risk for the electrical system components. 

Context

Precharge is required when a voltage source is connected to the converter with a power switch in between and that source does not have a built-in precharge. Suddenly closing the switch will cause a current surge for a moment, damaging the converter and the devices connected to it.

To limit this phenomenon, a resistor must be engaged in parallel with the switch before the latter closes. The purpose of this operation is to increase the current gradually in the converter. 

When the voltage across the resistor (therefore across the open switch) is less than 30V, the open switch can be closed without risk. When preloading needs to be done on the Low side and High side, preload the high side first. Even when the converter is not turned on (CAN off), if voltage is applied to its terminals (low and high side), damage can be caused. It is therefore necessary to preload the converter even when it is switched off.

Tame-Power contribution

Aware of the importance of the precharge of a powered up system, Tame-Power specially calculated precharges which are necessary to its DC DC converters. Moreover, Tame-Power HMI was specially designed to ensure support to precharge resistor dimensioning, in regard to the application system. 

Precharge dimensioning

All Tame-Power DC DC converters need a precharge prior to their commissioning. According to devices which are connected to the DC DC converter electrical architecture, there are different specific cases impacting the precharge sizing: 

  • Electrical architectures already including a precharge system 
  • Electrical architectures needing a precharge system either in low side or high side 
  • Electrical architectures needing a precharge system in both low side and high side 

Architectures including precharge systems for all devices 

If all devices connected to the electrical architecture already have an integrated precharge system, it is not necessary to add a precharge system to the electrical architecture. 

Architectures needing a precharge system in low side or in high side

When a precharge system is necessary either for low side or high side, a precharge system must be added to respective low side or high side terminals. Hence, only one additional precharge system is required. 

Architectures needing a precharge system in low side and high side 

Chen a precharge system is necessary for both low side and high side of the DC DC converter, it is necessary to provide two extra precharge systems for low side and high side terminals. Hence, two additional precharge systems are required. 

When a precharge is needed in both low side and high side, it is mandatory to precharge the high side first. 

Tame-Power solutions 

Prechare procedure 

Précharge DC DC

In order to limit damage risks for DC DC converters, Tame-Power developed a dedicated precharge sequence in reference to the layout above and as: 

  1. Close the swith 1 (SW1) to precharge the system
  2. Check that the resistor terminals is lower than 30V
  3. If yes, close the switch 2 (SW 2)
  4. Possibly, open the switch 1 (SW 1 - optional)

Precharge calculation  

Simple unit DC DC converters
CONVY L S / CONVY A / CISO L

  
 

Double unit DC DC converters
CONVY L D

Voltage R Precharge Voltage R Precharge
50 5 50 3
100 10 100 5
150 15 150 8
200 20 200 10
250 25 250 13
300 30 300 15
350 35 350 18
400 40 400 20
450 45 450 23
500 50 500 25
550 55 550 28
600 60 600 30
650 65 650 33
700 70 700 35
750 75 750 38
800 80 800 40

 

Tame-Power global offer

Markets

Power conversion and distribution solutions dedicated to on-board and stationary applications
See

Services

Building together the products that best fit your needs
See

Products

Innovative DCDC power conversion and power distribution solutions
See

Your Tame-Power contact person

  • Steven Horeau

    Field Support Engineer

    Steven is the Field Support Engineer for Tame-Power. He has been involved in customer support for nearly 10 years and provides after-sales service. At the same time, he participates in the continuous improvement of equipment in collaboration with technical management, production and the quality department.

    His missions :

    • Support you during the start-up and integration of our products into your applications,
    • Perform remote diagnostics,
    • Guide you through dedicated verification procedures.



26 rue du Bocage
85660 Saint-Philbert-de-Bouaine
FRANCE

Follow Tame-Power

Subscribe to the newsletter

Stay informed on Tame-Power news by subscribing to the newsletter

Subscribe

Distribute Tame-Power products

Become a distributor